When it comes to HVAC systems, there are two major components in the system; they are the outdoor condensing unit and the indoor air handler. The two components are designed to work side by side to provide optimal performance, maximum efficiency and comfort for everyone within the household. Whenever you have heating and air conditioning service in Dallas, TX and one of the two components is removed and a new one installed, it can compromise the efficiency and performance of the system. If the system is more than 10 years old, you should really consider purchasing a whole new system, gains in energy efficiency alone will pay for itself over time.
A properly sized matched system will enable the HVAC system to perform as designed. It will have proper cycle times, intended humidity control, and the system sound will be minimized. Features such as these, are likely to be lost or marginalized in a mismatched system. When an outdoor unit is replaced, it may be appealing due to the lower cost, but it is likely to cost you more over time due to the loss in maximum efficiency and it could possibly end up requiring you to need more heating and air conditioning service in Dallas, TX.
Sometimes mismatching is not always an option when you have heating and air conditioning service in Dallas, TX. However when it is an option, the system may work, but there will be other negative consequences involved with using a mismatched system. It will not provide the promised energy efficiency for one. In fact, you might lose as much as fifteen percent of the stated efficiency when you do so. Furthermore, comfort is likely to be compromised also. On the hottest days, a mismatched system may not likely perform up to par, nor be able to cool efficiency or properly remove enough humidity from the indoors. Finally, a mismatched system can overwork the system and it will require more heating and air conditioning service in Dallas, TX.
With today’s energy efficient HVAC systems, they are designed for greater energy efficiency, the components found in both the indoor and outdoor unit are designed to match the technology. The compressor is the most expensive component in a modern air conditioning system and because of this; it is extremely dependent upon proper system design and installation. A mismatched system may compromise this, resulting in premature death of the system.
An old indoor coil will most likely provide less heat transfer capability when paired with a newer, more energy efficient outside unit. Next, it will usually have an expansion device that will not be the correct size or designed for the use with the recommended refrigerant charge. Furthermore, the existing coil not being the proper design for the new outdoor condenser will increase the risk of compressor failure, requiring premature heating and air conditioning service in Dallas, TX.
A mismatched system is a gamble, and with as much as outdoor compressors cost, is it really worth that gamble? The chances of a compressor failing increases by as much as 45% within the first year. Also, mismatching a new condenser and compressor to an old, undersized coil and fixed expansion device is almost certainly going to result in failure, and this is why it is not covered under most heating and air conditioning manufacturer’s warranty coverage.
Furthermore, almost all utility companies will require that both components of an air conditioner or heat pump system be ARI certified and properly matched in order to quality for their rebate programs.
Despite all of the negatives and disadvantages of a mismatched system, a number of contractors and dealers are still routinely failing to replace the indoor coil with the installation of a new condensing unit. Few homeowners even realize the importance of a matching system for their HVAC system at home or that a critical component has failed to be installed.
Luckily, you can depend on Garland Heating and Air Conditioning’s NATE certified professional technicians to perform the job the right way the first time in all respects, including educating you and informing you on the importance of a matching system. Garland Heating and Air Conditioning in Dallas, TX only hires the best HVAC technicians in the area, to ensure that you receive the satisfaction that you expect, and the professionalism that you deserve. Give us a call for heating and air conditioning service in Dallas, TX or any other HVAC needs such as installation, and maintenance. You can count on Garland Heating and Air Conditioning.
About Garland Heating and Air Conditioning
Garland Heating and Air Conditioning has been helping homeowners and businesses alike in Dallas, Texas and surrounding areas for many years with heating and air conditioning service in Dallas, TX. We are one of the leading heating and air companies in the area. Dedication, determination and professional services that you can rely on have helped made us the go to source for customers in the area who are in need of heating and cooling repairs, installations and maintenance. When you contact Garland Heating and Air Conditioning in Dallas, Texas you can rest assured knowing that you are receiving high quality professional heating and air conditioning service in Dallas, TX that is both reliable and affordable.
Garland Heating and Air Conditioning in Dallas, Texas is a leader in the HVAC field servicing Dallas, Plano, and surrounding areas. Our NATE certified technicians provide professional HVAC related services, installation and repairs. If you are looking for help with your home or business’ HVAC system and need heating and air conditioning service in Dallas, TX do not hesitate to give us a call today. One of our professional technicians will be more than happy to assist you and schedule a service call heating and air conditioning service in Dallas, TX your earliest convenience. Garland Heating and Air Conditioning is a proud member of the BBB and maintains a rock solid A+ rating.